A-B 2094-BC07-M05-M Analog Output Module

Product Detailed Description:

The Allen-Bradley ControlLinks Actuator is a part of the ControlLinks system, which is designed to provide a simple, cost-effective, and reliable way to monitor and control discrete devices in industrial environments. The actuator component is typically an electromechanical device used to physically operate a switch or valve.

In the context of the ControlLinks system, the actuator works in conjunction with other ControlLinks components (like sensors and communication modules) to automate processes. It receives control signals, usually via the ControlLinks network, and translates these signals into mechanical motion to perform a specific function, such as opening or closing a valve, or toggling a switch. These actuators are often designed for direct mounting and easy integration into various control applications.

Product Parameters:

• Operating Voltage: Typically designed for common industrial voltages (e.g., 24V DC, 120V AC, 230V AC - specific voltage depends on the model).

• Operating Current: Varies by model and load.

• Communication Protocol: Uses the proprietary ControlLinks communication protocol over a two-wire bus system.

• Control Signal: Responds to digital control signals received over the ControlLinks network.

• Actuation Type: Can be spring-return (for fail-safe operation) or non-spring-return (for latched operation).

• Actuation Force/Stroke: Specifications vary depending on the specific actuator model and its intended application (e.g., valve size, switch type).

• Environmental Ratings: Often rated for industrial environments, including specific IP ratings (e.g., IP65) for protection against dust and water.

• Mounting: Typically designed for panel or direct mounting on the device being actuated.

• Network Topology: Supports a multi-drop network topology, allowing multiple devices to be connected on a single two-wire bus.

Product Advantages:

• Simplified Wiring: Utilizes a two-wire bus system, significantly reducing the amount of wiring required compared to traditional point-to-point wiring, leading to lower installation costs and easier troubleshooting.

• Reduced Costs: Lower material costs (less wire, fewer components) and reduced installation time contribute to overall project cost savings.

• Easy Installation and Commissioning: Plug-and-play design and straightforward configuration simplify setup and integration into existing or new systems.

• Scalability: The multi-drop network allows for easy expansion by adding more ControlLinks devices to the bus.

• Reliability: Designed for industrial environments, often featuring robust construction and diagnostic capabilities.

• Integrated Diagnostics: Many ControlLinks devices offer built-in diagnostics that can be monitored via the network, aiding in predictive maintenance and faster troubleshooting.

• Modularity: Part of a system where sensors, actuators, and communication modules can be mixed and matched.

Precautions / Important Notes:

• Power Supply: Ensure the power supply connected to the ControlLinks bus matches the requirements of the actuator and other devices on the network.

• Termination: Proper termination resistors must be installed at the end points of the ControlLinks bus to ensure reliable communication. Follow the specific installation guidelines.

• Network Configuration: Correctly configure the actuator’s address and parameters within the control system (e.g., PLC) to match its physical installation and desired operation.

• Environmental Conditions: Install the actuator within its specified temperature, humidity, and vibration limits. Protect it from excessive dust, moisture, or corrosive atmospheres if not rated for such conditions.

• Electrical Safety: De-energize the system and follow proper lockout/tagout (LOTO) procedures before performing any maintenance or installation work.

• Load Compatibility: Ensure the actuator is rated for the specific mechanical load it will be operating (e.g., valve size, switch type).

• Failure Mode: Understand the actuator’s failure mode (spring-return vs. non-spring-return) and how it affects the process in case of power loss or network failure.

• Documentation: Always refer to the specific product manual for detailed installation, wiring, operation, and safety instructions for the particular ControlLinks actuator model being used.

Product Applications:

The Allen-Bradley ControlLinks Actuator is well-suited for a wide range of industrial applications where simple, cost-effective control of discrete devices is needed, particularly in distributed control scenarios. Common applications include:

• Valve Actuation: Opening and closing solenoid valves, ball valves, butterfly valves, and other types of process valves in water/wastewater treatment, chemical processing, HVAC, and food & beverage industries.

• Switch Operation: Toggling mechanical switches or relays for various control functions.

• Pump Control: Starting and stopping pumps in simple on/off control loops.

• Conveyor Systems: Actuating components like diverters or stoppers on conveyor lines.

• Material Handling: Controlling gates or chutes in bulk material handling systems.

• Building Automation: Controlling dampers, valves, or other HVAC components in smaller or distributed building control systems.

• General Industrial Automation: Any application requiring simple, reliable on/off control of a mechanical device where a complex PLC I/O system is not necessary.

Shipping Port: Xiamen, China

Payment: Bank of Chicago, Bank of Singapor

Express cooperation: fedex, DHL, UPS and your express account

Service: Professional Sales provides 24 hours /7 days online service

Related products

E-mail: alex@fenoux.com

Tel.: +86 13338369201

Skype: +86  13338369201

WhatsApp: +86  13338369201