Bently 330180-91-00 Programmable controller

Bently Nevada 330180-91-00 Overview

The Bently Nevada 330180-91-00 is a non-contacting eddy current proximity transducer belonging to the 3300 XL series. It is typically used in conjunction with a 3300 XL extension cable and a monitor to form a complete displacement measurement system for monitoring shaft vibration, shaft position, and shaft speed on rotating machinery.

The specific meaning of the model 330180-91-00 is typically as follows:

• 330180: Indicates a 3300 XL 5 mm probe.

• 91: Indicates a total length of 9.1 inches (approximately 231.1 mm).

• 00: Indicates the connector option, usually no connector (requires hardwiring).

Product Detailed Description

• Function:

• Non-contact measurement of radial vibration of rotating machine shafts (relative to the bearing housing).

• Measurement of axial position (thrust bearing wear and axial movement).

• In conjunction with a Keyphasor* mark, can measure shaft speed and once-per-turn events.

• Outputs a voltage signal proportional to the distance between the probe tip and the observed metallic surface.

• Features:

• 5 mm (0.197 inch) probe tip diameter.

• 9.1 inches (231.1 mm) total length.

• No connector design for hardwiring.

• Requires use with a 3300 XL extension cable and a compatible Bently Nevada monitor.

• Rugged industrial design suitable for various rotating machinery monitoring applications.

Product Parameters

As this is a specific model, the following parameters are based on typical specifications for the 3300 XL 5 mm probe series. Always refer to the official datasheet for the 330180-91-00 model:

• Probe Tip Diameter: 5 mm (0.197 in)

• Total Length: 9.1 in (231.1 mm)

• Thread Size: M10 x 1 or 3/8-24 UNF (depending on specific sub-model)

• Cable Type: Coaxial cable

• Cable Length (Integral to Probe): Usually short, requires an extension cable

• Target Material: Any conductive metal

• Frequency Response: 0 to 10 kHz (-3 dB)

• Linear Range: Typically around 2.5 mm (0.100 in)

• Scale Factor (Sensitivity): Typically around 8.0 V/mm (200 mV/mil)

• Temperature Range:

• Operating: -51 °C to +177 °C (-60 °F to +350 °F)

• Storage: -51 °C to +204 °C (-60 °F to +400 °F)

• Connector: No connector (hardwired)

• Approvals: CE, ATEX, CSA (depending on specific certifications)

Product Advantages

• Non-Contacting Measurement: Eliminates physical contact between the sensor and rotating parts, reducing wear and improving reliability.

• High Accuracy and Resolution: Provides precise measurement of shaft vibration and position, aiding in early detection of machine faults.

• Wide Frequency Response: Capable of capturing a broad range of vibration frequencies.

• Rugged and Durable: Designed for reliable operation in harsh industrial environments.

• Proven Technology: The 3300 XL series is a well-established and reliable solution for rotating machinery protection.

• Early Fault Detection: By monitoring changes in key parameters, potential machine failures can be detected early, reducing downtime and maintenance costs.

Precautions

• Correct Installation: Follow Bently Nevada's installation guidelines, including proper probe gap setting and torque requirements.

• Use Matched Extension Cable and Monitor: Must be used with a compatible 3300 XL extension cable and Bently Nevada monitor to ensure proper system calibration and performance.

• Environmental Conditions: Avoid use in environments exceeding the probe's operating temperature range or where corrosive substances are present.

• Target Surface Condition: The surface of the shaft being measured should be clean and free of significant damage.

• Cable Routing: Ensure proper routing of the extension cable to avoid electromagnetic interference.

• Regular Inspection: Periodically inspect the probe, cable, and connections for any physical damage or looseness.

Product Applications

Bently Nevada 3300 XL proximity transducer systems (including the 330180-91-00 probe) are widely used for monitoring and protecting various types of rotating machinery:

• Steam and Gas Turbines: Shaft vibration and axial position monitoring.

• Compressors: Shaft vibration and axial position monitoring.

• Pumps: Shaft vibration and axial position monitoring.

• Motors and Generators: Shaft vibration monitoring.

• Gearboxes: Shaft vibration and axial position monitoring.

• Wind Turbines: Main shaft and gearbox monitoring.

• Any critical rotating equipment requiring continuous monitoring of shaft vibration and position.

Shipping Port: Xiamen, China